Go Back   The Navara Forum > Search Forums

Showing results 1 to 25 of 500
Search took 0.05 seconds.
Search: Posts Made By: Rumpig
Forum: D22 Engine 15-11-2019, 01:14 PM
Replies: 296
Views: 78,690
Posted By Rumpig
Hi, Yeah i use mcumalls GQ-4x , there's options...

Hi,
Yeah i use mcumalls GQ-4x , there's options in the software to select the chip type your writing to which needs to be pretty close , then i erase the chips, blank test them, write the files and...
Forum: D22 Engine 02-11-2019, 02:37 AM
Replies: 296
Views: 78,690
Posted By Rumpig
There's a cracked version 2.24 floating around...

There's a cracked version 2.24 floating around the net.
Forum: D22 Engine 01-11-2019, 02:25 PM
Replies: 296
Views: 78,690
Posted By Rumpig
The OLS i have won't work with the demo version....

The OLS i have won't work with the demo version. If i get motivated i might do an updated text file with all the map descriptions i know , don't hold your breath waiting thou.
Forum: D22 Engine 01-11-2019, 04:46 AM
Replies: 296
Views: 78,690
Posted By Rumpig
I haven't compared different years to see if...

I haven't compared different years to see if there were any changes so can't answer that
I have added some other map updates later in the thread but no new findings for a while , not sure if anyone...
Forum: D22 Engine 30-10-2019, 01:47 PM
Replies: 296
Views: 78,690
Posted By Rumpig
The map is fuel on one axis , rpm on the other...

The map is fuel on one axis , rpm on the other and the output is boost level as a percent . 100% being 15 psi. With out looking at the map i posted i probably only changed the fuel axis to make sure...
Forum: New Members Area 23-07-2019, 10:07 AM
Replies: 3
Views: 276
Posted By Rumpig
http://www.navara.asia/showpost.php?p=344796&postc...

http://www.navara.asia/showpost.php?p=344796&postcount=220
Forum: D22 Engine 09-02-2019, 11:57 AM
Replies: 296
Views: 78,690
Posted By Rumpig
Hi Beachdaz, i'm not suppling chips anymore and...

Hi Beachdaz,
i'm not suppling chips anymore and i'm not sure if Kevin at EFI autoparts is still socketing ecu's anymore. If Philb doesn't have his for sale anymore E.C.P.T https://ecpt.com.au are...
Forum: D22 Engine 09-11-2018, 05:02 AM
Replies: 8
Views: 2,006
Posted By Rumpig
I can take up hangliding again. Not enough wind...

I can take up hangliding again. Not enough wind for hangliding i'll go diving instead.
Forum: D22 Engine 08-11-2018, 07:50 AM
Replies: 8
Views: 2,006
Posted By Rumpig
Halfway , Geraldton.

Halfway , Geraldton.
Forum: D22 Engine 01-11-2018, 09:07 AM
Replies: 8
Views: 2,006
Posted By Rumpig
I just moved from Darwin to W.A , ute loaded up...

I just moved from Darwin to W.A , ute loaded up towing an enclosed trailer. Ecutalk showed 106 and the guage hadn't budged from it's normal postion of just under half. Didn't want to find out when it...
Forum: Main Forum 30-09-2018, 07:44 AM
Replies: 20
Views: 2,982
Posted By Rumpig
Not sure the 550 has a SCV , i've only heard it...

Not sure the 550 has a SCV , i've only heard it mentioned in relation to the 2.5 .
Forum: Main Forum 14-09-2018, 07:05 AM
Replies: 5
Views: 1,469
Posted By Rumpig
Possibly a faulty ABS sensor.

Possibly a faulty ABS sensor.
Forum: D22 Engine 13-09-2018, 05:28 AM
Replies: 96
Views: 6,738
Posted By Rumpig
Powercurve performance ended up getting 300hp out...

Powercurve performance ended up getting 300hp out of a ZD30. F55 turbo i think , +90% injectors , remap , custom intake manifold.
https://www.youtube.com/watch?v=A3Beb56qsnE
Forum: D22 Engine 09-09-2018, 12:00 PM
Replies: 96
Views: 6,738
Posted By Rumpig
13.1 and 46 are good values at idle for spill...

13.1 and 46 are good values at idle for spill valve and ICV%.
Good to see it going again.
Forum: D22 General Chat 08-08-2018, 07:40 AM
Replies: 23
Views: 4,678
Posted By Rumpig
The ecu board does get a coat of lacquer on it to...

The ecu board does get a coat of lacquer on it to prevent oxidation.
There's an atmo pressure sensor in them so they can't be air tight.
Forum: D22 General Chat 06-08-2018, 06:01 AM
Replies: 23
Views: 4,678
Posted By Rumpig
Probably should check the transfer case and front...

Probably should check the transfer case and front diff to, they might have water in them as well.
Forum: D22 General Chat 06-08-2018, 05:59 AM
Replies: 23
Views: 4,678
Posted By Rumpig
Ecu on the fuel pump should be sealed, wouldn't...

Ecu on the fuel pump should be sealed, wouldn't be a problem.
If you had water up to the bottom of the dash the ecu on top of the trans tunnel probably went under.
10mm socket to remove the 2...
Forum: D22 Engine 20-07-2018, 06:45 AM
Replies: 96
Views: 6,738
Posted By Rumpig
The lower outside wire is where you tap in...

The lower outside wire is where you tap in aftermarket chips (dp Tunit),and controls the spill valve for more fuel. The other pair are for the timing solenoid.

Google PSG16 repair, there are some...
Forum: D22 Engine 22-06-2018, 09:27 AM
Replies: 6
Views: 811
Posted By Rumpig
Sounds like he chipped it, not remapped it. Basic...

Sounds like he chipped it, not remapped it. Basic chips up the rail pressure, better ones extend the injection duration as well.
Forum: D22 General Chat 22-06-2018, 09:22 AM
Replies: 2
Views: 835
Posted By Rumpig
Good to hear it's back on the road, sounds like...

Good to hear it's back on the road, sounds like you went further than planned, pulling the head and all.
Forum: D22 Engine 18-06-2018, 11:47 AM
Replies: 296
Views: 78,690
Posted By Rumpig
The map at 397C2 limits the TPS voltage in 1st...

The map at 397C2 limits the TPS voltage in 1st and 2nd gear, before adding 25% to it I was only getting 1.7 volts in first and 2nd , after it's around 2.7v.
Didn't really seem to make any notable...
Forum: D22 Engine 18-06-2018, 11:40 AM
Replies: 296
Views: 78,690
Posted By Rumpig
The map at 3BC2A is the "start of injection"...

The map at 3BC2A is the "start of injection" limiter by temp. This limits the maximum injection point. There's no power gains from starting injection earlier but advancing it as you inject more fuel...
Forum: D22 Engine 18-06-2018, 11:34 AM
Replies: 296
Views: 78,690
Posted By Rumpig
For anyone that might be doing there own remaps,...

For anyone that might be doing there own remaps, to defeat the boost cut at 18 psi there is a 2d map at address 3BEB2 . The raw values are 2000, give it a 0.1 factor and it becomes 200mbar which is 3...
Forum: D22 Engine 12-06-2018, 11:19 AM
Replies: 6
Views: 760
Posted By Rumpig
Get them to give you the original chips once...

Get them to give you the original chips once they've desoldered them and you can stick them in and use them.
Forum: D22 Engine 13-05-2018, 01:32 AM
Replies: 22
Views: 4,211
Posted By Rumpig
ECM doesn't have an earth wire , it's the 2 bolts...

ECM doesn't have an earth wire , it's the 2 bolts that hold it to the trans tunnel.
Showing results 1 to 25 of 500

 
Forum Jump


All times are GMT +1. The time now is 07:10 AM.



Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
| Home | Register | FAQ | Members List | Calendar | Today's Posts | Search | New Posts |