Search results

Really good, no complaints, nothing hardcore just beach work. Only minor complaint could be the bolts rust like crazy, so they need looking after.

It seems every 40K I have been needing to get a wheel alignment (heavy wear of the inside camber) and the slop taken out of the steering box (10 - 15 degrees play in the steering wheel). Is this something all D22's suffer from or am I just lucky?

Thanks fellas. I bought the ROK hubs off Ebay. There were no AVM's listed but the ROK's look to be identical bar the branding. I will put them on over the weekend. A notable difference is the brass bush vs bearings in the OEM hubs.

Anyone used these ROK hubs? http://www.ebay.com.au/itm/ROK-FW-Manual-Hubs-Nisan-Pathfinder-V6-Navara-D21-D22-X-Terrain-/181168679846?hash=item2a2e7eaba6:g:6ZIAAOSw3ydVwFdV

I'm looking for a replacement set of hubs. Any recommendations? I wasn't sure of the exact number of splines, is it 28? Do you reckon these would fit...

Yes bods it worked. Thanks very much :)

Cheers. I will give it a go :)

I had the battery disconnected the other week and before I had the chance to enter the code, the kids (and their mother) had a go randomly pressing buttons; they locked the radio. :pissedoff: I have tried disconnecting the battery to see if it would reset. Nothing :deadhorse: Anyone have any...

I'm going to do my coolant this weekend. Manual differs from this description of where the cylinder block drain plug is. "Remove cylinder block drain plug located at left centre of cylinder block." Diagram shows it to be slightly rear of the oil filter drain pan. Can anyone confirm this?? Cheers

I have changed the oil in my 2005 D22 ZD30 STX (240,000 Ks) since new using Sakura or Ryco filters and Fuchs Titan Ultra Lube 15W40; changed every ~7000 ks. Never had a problem (touch wood :))

Would engine temp have anything to do with why my manifold is so clean? I have had the car since new and have always warmed (idled) it up before driving. EGR doesn't kick in before 1200rpm (?) and the car idles at 750rpm. Maybe the higher cylinder temps combusted the EGR gases more efficiently...

When I popped the EGR pipe to plate it last weekend the pipe was 1/3 blocked by carbon/oil crud. Thought I'd take off the manifold to clean it as it's never been done (and there was some crud in it). Probably wasn't necessary but only found that out once I had it off, but now its done I'm happy...

Fuchs Titan Ultralube 15W40 every 7000ks since new :)

Howdy, Big day, I just had the manifold off my 2005 with nearly 240,000 ks on the clock. I only did the EGR blanking last weekend so I reckon it looked pretty good for the ks. [/IMG]

If your after a cheaper saw the Makita saws are reported to be good. Makita took over Dolmar & Dolmar make pretty good saws :) http://www.dolmarpowerproducts.com/productcatalog/chain_saws_gasoline/index.html http://www.makita.com.au/products/power-garden-ope/petrol-chainsaws

I ditched my pre cleaner yesterday after work with one of these. I know I know it's about bloody time :)

A few years ago I bought a Stihl MS362 MC its a fantastic size/power and weight for firewood cutting & felling. It cost me $1360 which seemed expensive but its paid for itself many times over; $120 per cubic meter for wood delivered where I am. 10 minutes from home I can cut a ute load of...

The rubbers on my 2005 Nav are perishing, shrinking or cracking. Exterior window rubbers are shrinking, air intake rubber boot is cracking and the rubber strip along the black bonnet vent in perishing (Not to mention numerous other hoses & grommets etc.) Any one know where to find reasonably...

One for sale atm http://www.navara.asia/showthread.php?t=32096

Howdy fellas, Finally had a chance to do my front hubs. I had a mechanic do it once before and I think the suspension fellas had it apart when they did the suspension bushes. Anyhow the cir-clip on the LHS shaft is on the the inside of drive clutch rather than the outside. The shaft is too...