Recent content by sloba

Hi guys, I've since traded in my 2013 D40 ST however I was running 17x9 wheels with a +20 offset. If you search my old posts there should be a thread about my car with pictures. They were a good fit, increased the track slightly but didn't stick out the guards to much or anything. They were...

Hi guys, Just had a Tjm steel outback bar fitted to my 2013 d40. I noticed the little sticker that says anymore than 55kg needs hd front springs and a "positive bonnet restraint system" Now my question is I'm pretty sure this bar is a bit over this, I'm not fitting a winch or anything though...

If your after a throttle controller to include acceleration response times I also came across this one which might be a cheaper option at 4900 Thai baht. http://www.ecu-shop.com/boost-speed-pnp I saw some guy selling them on gumtree for 250aud also. Seem to be similar thing and are plug and...

Opted to get both , I asked what they did and they said the hook it up to some machine that hangs off the end of the rail and pumps cleaner thru it for the injector clean at least.. Figure I also may as well get the throttle body cleaned out . I do run the tank to pretty empty most times before...

Just sitting at nissan, my ute is in for its 30,000km service. Over and above the capped price service price the dealer also is recommending as preventative maintence to get an injector clean and throttle body clean done which will incur about another 200 bux each. Are they taking me for a...

4 x D40 17" wheels , no tyres. Off a 2012 . Good condition few small scratches. $450 firm , rather sell all together. Perth - South of river. Thanks, Mark 0401931167

cheers for the replies guys, to me the camber actually looked better on the initial specs from before they messed with it?? left looks ok , but right with the camber of 1.10 degrees I think it is , I'm pretty sure I can noticeably tell the right wheel has more positive camber when looking...

Hi guys So I had a lift installed in my 2013 d40 st 4x4 that consists of lovells shocks, dobinsons coils and efs leafs. Took the car for an alignment after however I've just noticed on the top of the spec sheet it seems to have a d22 navara.. Mine is a d40... My question is do the specs in...

The only place that lists the 740mm ones as 550 only as far as I can see is the fulcrum site... The efs catalog itself seems to state 2009+ is the nis-20e leaf. I also found a nz site selling efs leafs that seems to indicate the nis-17e leafs are pre facelift model navara and nis-20e post...

I recently ordered efs leafs from fulcrum and was asked to measure the middle of my leaf to the centre of the rear eye on the leaf by Matthew at hillcrst fulcrum ... . The measurement on my 2013 ST d40 was 740mm .. So I assume th niss20e will be sent to me? So it can't just be the 550 that...

Sold.

2013 Nissan Navara D40 17" Wheels / rims & Tyres x4 Taken off my brand new Navara, travelled just under 4000km on them. Tyres still 90% or better (almost brand new) 6x114.3 Stud Pattern 17x17 30 Offset 255/65/R17" GOODYEAR WRANGLER ALL WEATHER tyres Wheels present as BRAND NEW Condition...

I got my sports bar powder coated, much more durable and its not that expensive anyway.. I think it cost me $150 all up to get mine done in a gloss black, just another option instead of plasti dip

update with the new 17x9 rims and kuhmo kl78 265/70/17 AT tyres

thanks, That was another issue I was going to bring up - the bore of the centre of the wheels is 78mm and my hub is 66.1mm I believe, im going to purchase some hub rings (which half of them look piss weak anyway) but I've researched these alot on the net and speaking to people and there seems...