Recent content by Aus_Karlos

Hey guys im going to tackle the track this Saturday or Sunday (will confirm Tomorrow) Its been raining nicely so i'd thought i'd give it a go. Done the trips many times in the warmer, dryer months but never in winter. I've done the track many times solo, but if anyone was thinking of going just...

Long tile but it explains it well. Whenever i plug my trailer in without doing anything else my Hazard light relay fuse blows. All other lights still work including the separate indicators . It seems very strange as the Left and Right indicator cables are shared by the hazard light relay (Orange...

Had the same issue with my 3". The existing mounts when fitting 3" exhaust are too far apart for such a large exhaust. I use to get knocking when i turned the engine on/off. Went back to where i got it fitted and they modified some new brackets for me to secure the exhaust just below the...

I have a YD25 2008 4x4 model takes 5.5lts about 2mm below the full line. The manual says 4lts but it doesn't even register on the dipstick, ive done 6 or 7 oil changes and every time i use 5.5lts. Sometimes i takes the oil a while to get to all the small places. So i dump 5lts in wait for...

I own a DP chip, ive increased my boost whilst increasing the chips preset tune. Defiantly noticed a better response time for take off. But you do need to get rid of the stock exhaust its too small and will hinder what the chip is trying to do. About 2 years now Ive been running my DP chip...

The Engine light doesn't turn on if the starter motor is at fault. Sounds like a there's another issue with the car. Check your battery terminals and your Engine earth mounts. Do you have a OBDII scan tool that you could use to pull fault codes from the ECU? Sounds to me like your friend...

Ok well at least i know im in the ball park. When just driving normally changing gears around 2700rpm the rail gets to about 12000-18000psi. And when i put my foot down and change around 3500rpm the rail registers at 20000-26000psi (Depending on if its a flat surface or up hill) Teleman191...

Hey guys i'd like to know the maximum Fuel Rail Pressure the rail system can safely maintain. Ive been tweaking my fuel intake and boost pressure and its only just crossed my mind that i should be taking note of the fuel system aswell. Also using a OBD II link the ECU has a boost sensor. I...

The YD25 doesn't have the VAC lines. Well at least not on my YD25. You sure your not thinking of the 3lt version?

Yep thats what i did. From the Outlet side managed to get a small 5mm gap and squeeze the plate in.

Well i asked the questions to the auto-electricians and they've never seen anything like it as well. They suggest i take it into a mechanic to look at the transmission to make sure there's no heavy resistance on it. Unfortunately they couldn't take this starter motor apart to see the insides...

At the moment the Car is in with the Auto-Electrics, as this is the 3rd starter they have fitted they're kind enough to do this service for free. They're going to put a call out to the stater motors manufacture to see if this was a faulty batch but either way they are replacing it for free so...

Hey guys my Nav seems to be chewing through starter motors and i have no clue why. The latest one to go was only 10 months old, The only water its come in contact with was from puddles in the road. I do a lot of Dune driving and the odd rock climbs over on the PowerLine track in Perth. I get...

Does anyone trust the readings they get from an ODBII. Im using the Torque app for Android. I had set up my profile and began testing, found a nice quite road in an undeveloped area to see what HP reading i would get. After 6 test runs my Average Peak HP was 180.30HP (133KW) @ 1538rpm @ 19PSI...

Found out my Bluetooth for the radio is limited to phone calls as the blue tooth is controlled by the radio and not the tablet that sits in it. However the Tablet has a wireless adapter inside. Found a nice Android compatible OBD2 with a wireless connection. Also works with Iphones and Ipads for...