Power Loss
  #1  
Old 01-03-2019, 12:01 PM
Savage91 Savage91 is offline
Junior Member
 
Join Date: Mar 2019
Location: Innisfail
Posts: 1
Default Power Loss

Just Looking for some advice on a Nissan Navara D40 ST 2012. When driving sometimes it loses power, revs are up but wont go past 20 sometimes 40kmph. Ive heard it can maybe be in limp mode ...does anyone know how or what i need to do to fix it. We just paid over 2grand to get the fuel pump fixed. T
Reply With Quote
Sponsored Links

  #2  
Old 01-03-2019, 12:50 PM
Old.Tony's Avatar
Old.Tony Old.Tony is offline
Administrator
 
Join Date: Oct 2009
Location: Mid Coast Region, NSW, Australia
Posts: 15,014
My Mood:
Garage
Default

Limp mode is often accompanied by a "Check Engine Light" (CEL) and will have a code in the ECU that can be read.


You can put a bluetooth OBD adapter on your OBD port and read the code with any of a dozen or more Android apps. You could take it to a mechanic to read the code for you, or do the painful pedal switch sequence that makes the CEL flash a certain amount to spell out the 4-digit code. The first two options are the easiest.


The code will tell you why the ECU is putting the car in limp mode, but won't necessarily be the answer. You can reset it, as a first attempt, use either the bluetooth method or the mechanic method. The power-disconnect-foot-on-brake method may not work but it might be worth a try.


Example: bad earth. ECU is routing earth power through some other path because it's own earth point (right hand guard) is insufficient, and whatever that path is will result in an erroneous response and give you a false answer. You'd suspect a bad earth if you reset and get a weirdly different error the second time. Clean the earth by cleaning both battery posts, and checking the earth point near the ECU.


If you get consistent responses then it is likely to pretty close to the problem.


After working on the fuel pump, a reset of the fuel parameters should have been done, was it? This is the same as the forced-power-off method above, I'll describe that in detail:


1) Write down trip meter values if you use them
2) Get your radio PIN handy
3) Pop the bonnet yourself, lift it yourself, remove the battery negative lead yourself
4) Open the driver's door and press the brake yourself
5) Return the battery lead to the battery.


You cannot have an assistant help you. The entire point of the exercise is to dissipate energy in the ECU so that it does a basic reset (which won't clear severe diagnostic codes). A basic reset WILL reset the fuel mapping.


If you've had or tried a reset and it's still not working, grab that code and let us know what it is.
__________________

Check out the FAQs by clicking here!



"Money can't buy happiness, but it does make misery a lot easier to deal with."
Reply With Quote

  #3  
Old 01-03-2019, 09:23 PM
KevinE KevinE is offline
Member
 
Join Date: Dec 2011
Posts: 244
Default

It's most likely connected to your fuel pump re build.

I agree with the ECU reset as detailed by Tony.

If you have a dual battery system installed, disconnect it before you start the ECU re set.

If that doesn't work, I'd take it back to the guy who re built the fuel pump.

Good luck!
Reply With Quote

  #4  
Old 07-03-2019, 11:10 AM
Tms40's Avatar
Tms40 Tms40 is offline
Junior Member
 
Join Date: Mar 2017
Location: North Queensland
Posts: 25
My Mood:
Garage
Default

If no engine check light check your brake lights. Mine died in power due to brake light fault.
Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump



All times are GMT +1. The time now is 02:30 AM.



Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
| Home | Register | FAQ | Members List | Calendar | Today's Posts | Search | New Posts |